pci.h
上传用户:lgb322
上传日期:2013-02-24
资源大小:30529k
文件大小:31k
- /*
- * $Id: pci.h,v 1.87 1998/10/11 15:13:12 mj Exp $
- *
- * PCI defines and function prototypes
- * Copyright 1994, Drew Eckhardt
- * Copyright 1997--1999 Martin Mares <mj@ucw.cz>
- *
- * For more information, please consult the following manuals (look at
- * http://www.pcisig.com/ for how to get them):
- *
- * PCI BIOS Specification
- * PCI Local Bus Specification
- * PCI to PCI Bridge Specification
- * PCI System Design Guide
- */
- #ifndef LINUX_PCI_H
- #define LINUX_PCI_H
- /*
- * Under PCI, each device has 256 bytes of configuration address space,
- * of which the first 64 bytes are standardized as follows:
- */
- #define PCI_VENDOR_ID 0x00 /* 16 bits */
- #define PCI_DEVICE_ID 0x02 /* 16 bits */
- #define PCI_COMMAND 0x04 /* 16 bits */
- #define PCI_COMMAND_IO 0x1 /* Enable response in I/O space */
- #define PCI_COMMAND_MEMORY 0x2 /* Enable response in Memory space */
- #define PCI_COMMAND_MASTER 0x4 /* Enable bus mastering */
- #define PCI_COMMAND_SPECIAL 0x8 /* Enable response to special cycles */
- #define PCI_COMMAND_INVALIDATE 0x10 /* Use memory write and invalidate */
- #define PCI_COMMAND_VGA_PALETTE 0x20 /* Enable palette snooping */
- #define PCI_COMMAND_PARITY 0x40 /* Enable parity checking */
- #define PCI_COMMAND_WAIT 0x80 /* Enable address/data stepping */
- #define PCI_COMMAND_SERR 0x100 /* Enable SERR */
- #define PCI_COMMAND_FAST_BACK 0x200 /* Enable back-to-back writes */
- #define PCI_STATUS 0x06 /* 16 bits */
- #define PCI_STATUS_CAP_LIST 0x10 /* Support Capability List */
- #define PCI_STATUS_66MHZ 0x20 /* Support 66 Mhz PCI 2.1 bus */
- #define PCI_STATUS_UDF 0x40 /* Support User Definable Features [obsolete] */
- #define PCI_STATUS_FAST_BACK 0x80 /* Accept fast-back to back */
- #define PCI_STATUS_PARITY 0x100 /* Detected parity error */
- #define PCI_STATUS_DEVSEL_MASK 0x600 /* DEVSEL timing */
- #define PCI_STATUS_DEVSEL_FAST 0x000
- #define PCI_STATUS_DEVSEL_MEDIUM 0x200
- #define PCI_STATUS_DEVSEL_SLOW 0x400
- #define PCI_STATUS_SIG_TARGET_ABORT 0x800 /* Set on target abort */
- #define PCI_STATUS_REC_TARGET_ABORT 0x1000 /* Master ack of " */
- #define PCI_STATUS_REC_MASTER_ABORT 0x2000 /* Set on master abort */
- #define PCI_STATUS_SIG_SYSTEM_ERROR 0x4000 /* Set when we drive SERR */
- #define PCI_STATUS_DETECTED_PARITY 0x8000 /* Set on parity error */
- #define PCI_CLASS_REVISION 0x08 /* High 24 bits are class, low 8
- revision */
- #define PCI_REVISION_ID 0x08 /* Revision ID */
- #define PCI_CLASS_PROG 0x09 /* Reg. Level Programming Interface */
- #define PCI_CLASS_DEVICE 0x0a /* Device class */
- #define PCI_CACHE_LINE_SIZE 0x0c /* 8 bits */
- #define PCI_LATENCY_TIMER 0x0d /* 8 bits */
- #define PCI_HEADER_TYPE 0x0e /* 8 bits */
- #define PCI_HEADER_TYPE_NORMAL 0
- #define PCI_HEADER_TYPE_BRIDGE 1
- #define PCI_HEADER_TYPE_CARDBUS 2
- #define PCI_BIST 0x0f /* 8 bits */
- #define PCI_BIST_CODE_MASK 0x0f /* Return result */
- #define PCI_BIST_START 0x40 /* 1 to start BIST, 2 secs or less */
- #define PCI_BIST_CAPABLE 0x80 /* 1 if BIST capable */
- /*
- * Base addresses specify locations in memory or I/O space.
- * Decoded size can be determined by writing a value of
- * 0xffffffff to the register, and reading it back. Only
- * 1 bits are decoded.
- */
- #define PCI_BASE_ADDRESS_0 0x10 /* 32 bits */
- #define PCI_BASE_ADDRESS_1 0x14 /* 32 bits [htype 0,1 only] */
- #define PCI_BASE_ADDRESS_2 0x18 /* 32 bits [htype 0 only] */
- #define PCI_BASE_ADDRESS_3 0x1c /* 32 bits */
- #define PCI_BASE_ADDRESS_4 0x20 /* 32 bits */
- #define PCI_BASE_ADDRESS_5 0x24 /* 32 bits */
- #define PCI_BASE_ADDRESS_SPACE 0x01 /* 0 = memory, 1 = I/O */
- #define PCI_BASE_ADDRESS_SPACE_IO 0x01
- #define PCI_BASE_ADDRESS_SPACE_MEMORY 0x00
- #define PCI_BASE_ADDRESS_MEM_TYPE_MASK 0x06
- #define PCI_BASE_ADDRESS_MEM_TYPE_32 0x00 /* 32 bit address */
- #define PCI_BASE_ADDRESS_MEM_TYPE_1M 0x02 /* Below 1M [obsolete] */
- #define PCI_BASE_ADDRESS_MEM_TYPE_64 0x04 /* 64 bit address */
- #define PCI_BASE_ADDRESS_MEM_PREFETCH 0x08 /* prefetchable? */
- #define PCI_BASE_ADDRESS_MEM_MASK (~0x0fUL)
- #define PCI_BASE_ADDRESS_IO_MASK (~0x03UL)
- /* bit 1 is reserved if address_space = 1 */
- /* Header type 0 (normal devices) */
- #define PCI_CARDBUS_CIS 0x28
- #define PCI_SUBSYSTEM_VENDOR_ID 0x2c
- #define PCI_SUBSYSTEM_ID 0x2e
- #define PCI_ROM_ADDRESS 0x30 /* Bits 31..11 are address, 10..1 reserved */
- #define PCI_ROM_ADDRESS_ENABLE 0x01
- #define PCI_ROM_ADDRESS_MASK (~0x7ffUL)
- #define PCI_CAPABILITY_LIST 0x34 /* Offset of first capability list entry */
- /* 0x35-0x3b are reserved */
- #define PCI_INTERRUPT_LINE 0x3c /* 8 bits */
- #define PCI_INTERRUPT_PIN 0x3d /* 8 bits */
- #define PCI_MIN_GNT 0x3e /* 8 bits */
- #define PCI_MAX_LAT 0x3f /* 8 bits */
- /* Header type 1 (PCI-to-PCI bridges) */
- #define PCI_PRIMARY_BUS 0x18 /* Primary bus number */
- #define PCI_SECONDARY_BUS 0x19 /* Secondary bus number */
- #define PCI_SUBORDINATE_BUS 0x1a /* Highest bus number behind the bridge */
- #define PCI_SEC_LATENCY_TIMER 0x1b /* Latency timer for secondary interface */
- #define PCI_IO_BASE 0x1c /* I/O range behind the bridge */
- #define PCI_IO_LIMIT 0x1d
- #define PCI_IO_RANGE_TYPE_MASK 0x0fUL /* I/O bridging type */
- #define PCI_IO_RANGE_TYPE_16 0x00
- #define PCI_IO_RANGE_TYPE_32 0x01
- #define PCI_IO_RANGE_MASK (~0x0fUL)
- #define PCI_SEC_STATUS 0x1e /* Secondary status register, only bit 14 used */
- #define PCI_MEMORY_BASE 0x20 /* Memory range behind */
- #define PCI_MEMORY_LIMIT 0x22
- #define PCI_MEMORY_RANGE_TYPE_MASK 0x0fUL
- #define PCI_MEMORY_RANGE_MASK (~0x0fUL)
- #define PCI_PREF_MEMORY_BASE 0x24 /* Prefetchable memory range behind */
- #define PCI_PREF_MEMORY_LIMIT 0x26
- #define PCI_PREF_RANGE_TYPE_MASK 0x0fUL
- #define PCI_PREF_RANGE_TYPE_32 0x00
- #define PCI_PREF_RANGE_TYPE_64 0x01
- #define PCI_PREF_RANGE_MASK (~0x0fUL)
- #define PCI_PREF_BASE_UPPER32 0x28 /* Upper half of prefetchable memory range */
- #define PCI_PREF_LIMIT_UPPER32 0x2c
- #define PCI_IO_BASE_UPPER16 0x30 /* Upper half of I/O addresses */
- #define PCI_IO_LIMIT_UPPER16 0x32
- /* 0x34 same as for htype 0 */
- /* 0x35-0x3b is reserved */
- #define PCI_ROM_ADDRESS1 0x38 /* Same as PCI_ROM_ADDRESS, but for htype 1 */
- /* 0x3c-0x3d are same as for htype 0 */
- #define PCI_BRIDGE_CONTROL 0x3e
- #define PCI_BRIDGE_CTL_PARITY 0x01 /* Enable parity detection on secondary interface */
- #define PCI_BRIDGE_CTL_SERR 0x02 /* The same for SERR forwarding */
- #define PCI_BRIDGE_CTL_NO_ISA 0x04 /* Disable bridging of ISA ports */
- #define PCI_BRIDGE_CTL_VGA 0x08 /* Forward VGA addresses */
- #define PCI_BRIDGE_CTL_MASTER_ABORT 0x20 /* Report master aborts */
- #define PCI_BRIDGE_CTL_BUS_RESET 0x40 /* Secondary bus reset */
- #define PCI_BRIDGE_CTL_FAST_BACK 0x80 /* Fast Back2Back enabled on secondary interface */
- /* Header type 2 (CardBus bridges) */
- #define PCI_CB_CAPABILITY_LIST 0x14
- /* 0x15 reserved */
- #define PCI_CB_SEC_STATUS 0x16 /* Secondary status */
- #define PCI_CB_PRIMARY_BUS 0x18 /* PCI bus number */
- #define PCI_CB_CARD_BUS 0x19 /* CardBus bus number */
- #define PCI_CB_SUBORDINATE_BUS 0x1a /* Subordinate bus number */
- #define PCI_CB_LATENCY_TIMER 0x1b /* CardBus latency timer */
- #define PCI_CB_MEMORY_BASE_0 0x1c
- #define PCI_CB_MEMORY_LIMIT_0 0x20
- #define PCI_CB_MEMORY_BASE_1 0x24
- #define PCI_CB_MEMORY_LIMIT_1 0x28
- #define PCI_CB_IO_BASE_0 0x2c
- #define PCI_CB_IO_BASE_0_HI 0x2e
- #define PCI_CB_IO_LIMIT_0 0x30
- #define PCI_CB_IO_LIMIT_0_HI 0x32
- #define PCI_CB_IO_BASE_1 0x34
- #define PCI_CB_IO_BASE_1_HI 0x36
- #define PCI_CB_IO_LIMIT_1 0x38
- #define PCI_CB_IO_LIMIT_1_HI 0x3a
- #define PCI_CB_IO_RANGE_MASK (~0x03UL)
- /* 0x3c-0x3d are same as for htype 0 */
- #define PCI_CB_BRIDGE_CONTROL 0x3e
- #define PCI_CB_BRIDGE_CTL_PARITY 0x01 /* Similar to standard bridge control register */
- #define PCI_CB_BRIDGE_CTL_SERR 0x02
- #define PCI_CB_BRIDGE_CTL_ISA 0x04
- #define PCI_CB_BRIDGE_CTL_VGA 0x08
- #define PCI_CB_BRIDGE_CTL_MASTER_ABORT 0x20
- #define PCI_CB_BRIDGE_CTL_CB_RESET 0x40 /* CardBus reset */
- #define PCI_CB_BRIDGE_CTL_16BIT_INT 0x80 /* Enable interrupt for 16-bit cards */
- #define PCI_CB_BRIDGE_CTL_PREFETCH_MEM0 0x100 /* Prefetch enable for both memory regions */
- #define PCI_CB_BRIDGE_CTL_PREFETCH_MEM1 0x200
- #define PCI_CB_BRIDGE_CTL_POST_WRITES 0x400
- #define PCI_CB_SUBSYSTEM_VENDOR_ID 0x40
- #define PCI_CB_SUBSYSTEM_ID 0x42
- #define PCI_CB_LEGACY_MODE_BASE 0x44 /* 16-bit PC Card legacy mode base address (ExCa) */
- /* 0x48-0x7f reserved */
- /* Capability lists */
- #define PCI_CAP_LIST_ID 0 /* Capability ID */
- #define PCI_CAP_ID_PM 0x01 /* Power Management */
- #define PCI_CAP_ID_AGP 0x02 /* Accelerated Graphics Port */
- #define PCI_CAP_ID_VPD 0x03 /* Vital Product Data */
- #define PCI_CAP_ID_SLOTID 0x04 /* Slot Identification */
- #define PCI_CAP_ID_MSI 0x05 /* Message Signalled Interrupts */
- #define PCI_CAP_ID_CHSWP 0x06 /* CompactPCI HotSwap */
- #define PCI_CAP_LIST_NEXT 1 /* Next capability in the list */
- #define PCI_CAP_FLAGS 2 /* Capability defined flags (16 bits) */
- #define PCI_CAP_SIZEOF 4
- /* Power Management Registers */
- #define PCI_PM_PMC 2 /* PM Capabilities Register */
- #define PCI_PM_CAP_VER_MASK 0x0007 /* Version */
- #define PCI_PM_CAP_PME_CLOCK 0x0008 /* PME clock required */
- #define PCI_PM_CAP_RESERVED 0x0010 /* Reserved field */
- #define PCI_PM_CAP_DSI 0x0020 /* Device specific initialization */
- #define PCI_PM_CAP_AUX_POWER 0x01C0 /* Auxilliary power support mask */
- #define PCI_PM_CAP_D1 0x0200 /* D1 power state support */
- #define PCI_PM_CAP_D2 0x0400 /* D2 power state support */
- #define PCI_PM_CAP_PME 0x0800 /* PME pin supported */
- #define PCI_PM_CAP_PME_MASK 0xF800 /* PME Mask of all supported states */
- #define PCI_PM_CAP_PME_D0 0x0800 /* PME# from D0 */
- #define PCI_PM_CAP_PME_D1 0x1000 /* PME# from D1 */
- #define PCI_PM_CAP_PME_D2 0x2000 /* PME# from D2 */
- #define PCI_PM_CAP_PME_D3 0x4000 /* PME# from D3 (hot) */
- #define PCI_PM_CAP_PME_D3cold 0x8000 /* PME# from D3 (cold) */
- #define PCI_PM_CTRL 4 /* PM control and status register */
- #define PCI_PM_CTRL_STATE_MASK 0x0003 /* Current power state (D0 to D3) */
- #define PCI_PM_CTRL_PME_ENABLE 0x0100 /* PME pin enable */
- #define PCI_PM_CTRL_DATA_SEL_MASK 0x1e00 /* Data select (??) */
- #define PCI_PM_CTRL_DATA_SCALE_MASK 0x6000 /* Data scale (??) */
- #define PCI_PM_CTRL_PME_STATUS 0x8000 /* PME pin status */
- #define PCI_PM_PPB_EXTENSIONS 6 /* PPB support extensions (??) */
- #define PCI_PM_PPB_B2_B3 0x40 /* Stop clock when in D3hot (??) */
- #define PCI_PM_BPCC_ENABLE 0x80 /* Bus power/clock control enable (??) */
- #define PCI_PM_DATA_REGISTER 7 /* (??) */
- #define PCI_PM_SIZEOF 8
- /* AGP registers */
- #define PCI_AGP_VERSION 2 /* BCD version number */
- #define PCI_AGP_RFU 3 /* Rest of capability flags */
- #define PCI_AGP_STATUS 4 /* Status register */
- #define PCI_AGP_STATUS_RQ_MASK 0xff000000 /* Maximum number of requests - 1 */
- #define PCI_AGP_STATUS_SBA 0x0200 /* Sideband addressing supported */
- #define PCI_AGP_STATUS_64BIT 0x0020 /* 64-bit addressing supported */
- #define PCI_AGP_STATUS_FW 0x0010 /* FW transfers supported */
- #define PCI_AGP_STATUS_RATE4 0x0004 /* 4x transfer rate supported */
- #define PCI_AGP_STATUS_RATE2 0x0002 /* 2x transfer rate supported */
- #define PCI_AGP_STATUS_RATE1 0x0001 /* 1x transfer rate supported */
- #define PCI_AGP_COMMAND 8 /* Control register */
- #define PCI_AGP_COMMAND_RQ_MASK 0xff000000 /* Master: Maximum number of requests */
- #define PCI_AGP_COMMAND_SBA 0x0200 /* Sideband addressing enabled */
- #define PCI_AGP_COMMAND_AGP 0x0100 /* Allow processing of AGP transactions */
- #define PCI_AGP_COMMAND_64BIT 0x0020 /* Allow processing of 64-bit addresses */
- #define PCI_AGP_COMMAND_FW 0x0010 /* Force FW transfers */
- #define PCI_AGP_COMMAND_RATE4 0x0004 /* Use 4x rate */
- #define PCI_AGP_COMMAND_RATE2 0x0002 /* Use 2x rate */
- #define PCI_AGP_COMMAND_RATE1 0x0001 /* Use 1x rate */
- #define PCI_AGP_SIZEOF 12
- /* Slot Identification */
- #define PCI_SID_ESR 2 /* Expansion Slot Register */
- #define PCI_SID_ESR_NSLOTS 0x1f /* Number of expansion slots available */
- #define PCI_SID_ESR_FIC 0x20 /* First In Chassis Flag */
- #define PCI_SID_CHASSIS_NR 3 /* Chassis Number */
- /* Message Signalled Interrupts registers */
- #define PCI_MSI_FLAGS 2 /* Various flags */
- #define PCI_MSI_FLAGS_64BIT 0x80 /* 64-bit addresses allowed */
- #define PCI_MSI_FLAGS_QSIZE 0x70 /* Message queue size configured */
- #define PCI_MSI_FLAGS_QMASK 0x0e /* Maximum queue size available */
- #define PCI_MSI_FLAGS_ENABLE 0x01 /* MSI feature enabled */
- #define PCI_MSI_RFU 3 /* Rest of capability flags */
- #define PCI_MSI_ADDRESS_LO 4 /* Lower 32 bits */
- #define PCI_MSI_ADDRESS_HI 8 /* Upper 32 bits (if PCI_MSI_FLAGS_64BIT set) */
- #define PCI_MSI_DATA_32 8 /* 16 bits of data for 32-bit devices */
- #define PCI_MSI_DATA_64 12 /* 16 bits of data for 64-bit devices */
- /* Include the ID list */
- #include <linux/pci_ids.h>
- /*
- * The PCI interface treats multi-function devices as independent
- * devices. The slot/function address of each device is encoded
- * in a single byte as follows:
- *
- * 7:3 = slot
- * 2:0 = function
- */
- #define PCI_DEVFN(slot,func) ((((slot) & 0x1f) << 3) | ((func) & 0x07))
- #define PCI_SLOT(devfn) (((devfn) >> 3) & 0x1f)
- #define PCI_FUNC(devfn) ((devfn) & 0x07)
- /* Ioctls for /proc/bus/pci/X/Y nodes. */
- #define PCIIOC_BASE ('P' << 24 | 'C' << 16 | 'I' << 8)
- #define PCIIOC_CONTROLLER (PCIIOC_BASE | 0x00) /* Get controller for PCI device. */
- #define PCIIOC_MMAP_IS_IO (PCIIOC_BASE | 0x01) /* Set mmap state to I/O space. */
- #define PCIIOC_MMAP_IS_MEM (PCIIOC_BASE | 0x02) /* Set mmap state to MEM space. */
- #define PCIIOC_WRITE_COMBINE (PCIIOC_BASE | 0x03) /* Enable/disable write-combining. */
- #ifdef __KERNEL__
- #include <linux/types.h>
- #include <linux/config.h>
- #include <linux/ioport.h>
- #include <linux/list.h>
- #include <linux/errno.h>
- /* File state for mmap()s on /proc/bus/pci/X/Y */
- enum pci_mmap_state {
- pci_mmap_io,
- pci_mmap_mem
- };
- /* This defines the direction arg to the DMA mapping routines. */
- #define PCI_DMA_BIDIRECTIONAL 0
- #define PCI_DMA_TODEVICE 1
- #define PCI_DMA_FROMDEVICE 2
- #define PCI_DMA_NONE 3
- #define DEVICE_COUNT_COMPATIBLE 4
- #define DEVICE_COUNT_IRQ 2
- #define DEVICE_COUNT_DMA 2
- #define DEVICE_COUNT_RESOURCE 12
- #define PCI_ANY_ID (~0)
- #define pci_present pcibios_present
- #define pci_for_each_dev_reverse(dev)
- for(dev = pci_dev_g(pci_devices.prev); dev != pci_dev_g(&pci_devices); dev = pci_dev_g(dev->global_list.prev))
- #define pci_for_each_bus(bus)
- for(bus = pci_bus_b(pci_root_buses.next); bus != pci_bus_b(&pci_root_buses); bus = pci_bus_b(bus->node.next))
- /*
- * The pci_dev structure is used to describe both PCI and ISAPnP devices.
- */
- struct pci_dev {
- struct list_head global_list; /* node in list of all PCI devices */
- struct list_head bus_list; /* node in per-bus list */
- struct pci_bus *bus; /* bus this device is on */
- struct pci_bus *subordinate; /* bus this device bridges to */
- void *sysdata; /* hook for sys-specific extension */
- struct proc_dir_entry *procent; /* device entry in /proc/bus/pci */
- unsigned int devfn; /* encoded device & function index */
- unsigned short vendor;
- unsigned short device;
- unsigned short subsystem_vendor;
- unsigned short subsystem_device;
- unsigned int class; /* 3 bytes: (base,sub,prog-if) */
- u8 hdr_type; /* PCI header type (`multi' flag masked out) */
- u8 rom_base_reg; /* which config register controls the ROM */
- struct pci_driver *driver; /* which driver has allocated this device */
- void *driver_data; /* data private to the driver */
- u64 dma_mask; /* Mask of the bits of bus address this
- device implements. Normally this is
- 0xffffffff. You only need to change
- this if your device has broken DMA
- or supports 64-bit transfers. */
- u32 current_state; /* Current operating state. In ACPI-speak,
- this is D0-D3, D0 being fully functional,
- and D3 being off. */
- /* device is compatible with these IDs */
- unsigned short vendor_compatible[DEVICE_COUNT_COMPATIBLE];
- unsigned short device_compatible[DEVICE_COUNT_COMPATIBLE];
- /*
- * Instead of touching interrupt line and base address registers
- * directly, use the values stored here. They might be different!
- */
- unsigned int irq;
- struct resource resource[DEVICE_COUNT_RESOURCE]; /* I/O and memory regions + expansion ROMs */
- struct resource dma_resource[DEVICE_COUNT_DMA];
- struct resource irq_resource[DEVICE_COUNT_IRQ];
- char name[80]; /* device name */
- char slot_name[8]; /* slot name */
- u32 saved_state[16]; /* for saving the config space before suspend */
- int active; /* ISAPnP: device is active */
- int ro; /* ISAPnP: read only */
- unsigned short regs; /* ISAPnP: supported registers */
- int (*prepare)(struct pci_dev *dev); /* ISAPnP hooks */
- int (*activate)(struct pci_dev *dev);
- int (*deactivate)(struct pci_dev *dev);
- };
- #define pci_dev_g(n) list_entry(n, struct pci_dev, global_list)
- #define pci_dev_b(n) list_entry(n, struct pci_dev, bus_list)
- /*
- * For PCI devices, the region numbers are assigned this way:
- *
- * 0-5 standard PCI regions
- * 6 expansion ROM
- * 7-10 bridges: address space assigned to buses behind the bridge
- */
- #define PCI_ROM_RESOURCE 6
- #define PCI_BRIDGE_RESOURCES 7
- #define PCI_NUM_RESOURCES 11
-
- #define PCI_REGION_FLAG_MASK 0x0fU /* These bits of resource flags tell us the PCI region flags */
- struct pci_bus {
- struct list_head node; /* node in list of buses */
- struct pci_bus *parent; /* parent bus this bridge is on */
- struct list_head children; /* list of child buses */
- struct list_head devices; /* list of devices on this bus */
- struct pci_dev *self; /* bridge device as seen by parent */
- struct resource *resource[4]; /* address space routed to this bus */
- struct pci_ops *ops; /* configuration access functions */
- void *sysdata; /* hook for sys-specific extension */
- struct proc_dir_entry *procdir; /* directory entry in /proc/bus/pci */
- unsigned char number; /* bus number */
- unsigned char primary; /* number of primary bridge */
- unsigned char secondary; /* number of secondary bridge */
- unsigned char subordinate; /* max number of subordinate buses */
- char name[48];
- unsigned short vendor;
- unsigned short device;
- unsigned int serial; /* serial number */
- unsigned char pnpver; /* Plug & Play version */
- unsigned char productver; /* product version */
- unsigned char checksum; /* if zero - checksum passed */
- unsigned char pad1;
- };
- #define pci_bus_b(n) list_entry(n, struct pci_bus, node)
- extern struct list_head pci_root_buses; /* list of all known PCI buses */
- extern struct list_head pci_devices; /* list of all devices */
- /*
- * Error values that may be returned by PCI functions.
- */
- #define PCIBIOS_SUCCESSFUL 0x00
- #define PCIBIOS_FUNC_NOT_SUPPORTED 0x81
- #define PCIBIOS_BAD_VENDOR_ID 0x83
- #define PCIBIOS_DEVICE_NOT_FOUND 0x86
- #define PCIBIOS_BAD_REGISTER_NUMBER 0x87
- #define PCIBIOS_SET_FAILED 0x88
- #define PCIBIOS_BUFFER_TOO_SMALL 0x89
- /* Low-level architecture-dependent routines */
- struct pci_ops {
- int (*read_byte)(struct pci_dev *, int where, u8 *val);
- int (*read_word)(struct pci_dev *, int where, u16 *val);
- int (*read_dword)(struct pci_dev *, int where, u32 *val);
- int (*write_byte)(struct pci_dev *, int where, u8 val);
- int (*write_word)(struct pci_dev *, int where, u16 val);
- int (*write_dword)(struct pci_dev *, int where, u32 val);
- };
- struct pbus_set_ranges_data
- {
- int found_vga:1;
- int prefetch_valid:1;
- unsigned long io_start, io_end;
- unsigned long mem_start, mem_end;
- unsigned long prefetch_start, prefetch_end;
- };
- struct pci_device_id {
- unsigned int vendor, device; /* Vendor and device ID or PCI_ANY_ID */
- unsigned int subvendor, subdevice; /* Subsystem ID's or PCI_ANY_ID */
- unsigned int class, class_mask; /* (class,subclass,prog-if) triplet */
- unsigned long driver_data; /* Data private to the driver */
- };
- struct pci_driver {
- struct list_head node;
- char *name;
- const struct pci_device_id *id_table; /* NULL if wants all devices */
- int (*probe) (struct pci_dev *dev, const struct pci_device_id *id); /* New device inserted */
- void (*remove) (struct pci_dev *dev); /* Device removed (NULL if not a hot-plug capable driver) */
- int (*save_state) (struct pci_dev *dev, u32 state); /* Save Device Context */
- int (*suspend)(struct pci_dev *dev, u32 state); /* Device suspended */
- int (*resume) (struct pci_dev *dev); /* Device woken up */
- int (*enable_wake) (struct pci_dev *dev, u32 state, int enable); /* Enable wake event */
- };
- /* these external functions are only available when PCI support is enabled */
- #ifdef CONFIG_PCI
- #define pci_for_each_dev(dev)
- for(dev = pci_dev_g(pci_devices.next); dev != pci_dev_g(&pci_devices); dev = pci_dev_g(dev->global_list.next))
- void pcibios_init(void);
- void pcibios_fixup_bus(struct pci_bus *);
- int pcibios_enable_device(struct pci_dev *);
- char *pcibios_setup (char *str);
- /* Used only when drivers/pci/setup.c is used */
- void pcibios_align_resource(void *, struct resource *, unsigned long);
- void pcibios_update_resource(struct pci_dev *, struct resource *,
- struct resource *, int);
- void pcibios_update_irq(struct pci_dev *, int irq);
- void pcibios_fixup_pbus_ranges(struct pci_bus *, struct pbus_set_ranges_data *);
- /* Backward compatibility, don't use in new code! */
- int pcibios_present(void);
- int pcibios_read_config_byte (unsigned char bus, unsigned char dev_fn,
- unsigned char where, unsigned char *val);
- int pcibios_read_config_word (unsigned char bus, unsigned char dev_fn,
- unsigned char where, unsigned short *val);
- int pcibios_read_config_dword (unsigned char bus, unsigned char dev_fn,
- unsigned char where, unsigned int *val);
- int pcibios_write_config_byte (unsigned char bus, unsigned char dev_fn,
- unsigned char where, unsigned char val);
- int pcibios_write_config_word (unsigned char bus, unsigned char dev_fn,
- unsigned char where, unsigned short val);
- int pcibios_write_config_dword (unsigned char bus, unsigned char dev_fn,
- unsigned char where, unsigned int val);
- int pcibios_find_class (unsigned int class_code, unsigned short index, unsigned char *bus, unsigned char *dev_fn);
- int pcibios_find_device (unsigned short vendor, unsigned short dev_id,
- unsigned short index, unsigned char *bus,
- unsigned char *dev_fn);
- /* Generic PCI functions used internally */
- void pci_init(void);
- int pci_bus_exists(const struct list_head *list, int nr);
- struct pci_bus *pci_scan_bus(int bus, struct pci_ops *ops, void *sysdata);
- struct pci_bus *pci_alloc_primary_bus(int bus);
- struct pci_dev *pci_scan_slot(struct pci_dev *temp);
- int pci_proc_attach_device(struct pci_dev *dev);
- int pci_proc_detach_device(struct pci_dev *dev);
- int pci_proc_attach_bus(struct pci_bus *bus);
- int pci_proc_detach_bus(struct pci_bus *bus);
- void pci_name_device(struct pci_dev *dev);
- char *pci_class_name(u32 class);
- void pci_read_bridge_bases(struct pci_bus *child);
- struct resource *pci_find_parent_resource(const struct pci_dev *dev, struct resource *res);
- int pci_setup_device(struct pci_dev *dev);
- int pci_get_interrupt_pin(struct pci_dev *dev, struct pci_dev **bridge);
- /* Generic PCI functions exported to card drivers */
- struct pci_dev *pci_find_device (unsigned int vendor, unsigned int device, const struct pci_dev *from);
- struct pci_dev *pci_find_subsys (unsigned int vendor, unsigned int device,
- unsigned int ss_vendor, unsigned int ss_device,
- const struct pci_dev *from);
- struct pci_dev *pci_find_class (unsigned int class, const struct pci_dev *from);
- struct pci_dev *pci_find_slot (unsigned int bus, unsigned int devfn);
- int pci_find_capability (struct pci_dev *dev, int cap);
- int pci_read_config_byte(struct pci_dev *dev, int where, u8 *val);
- int pci_read_config_word(struct pci_dev *dev, int where, u16 *val);
- int pci_read_config_dword(struct pci_dev *dev, int where, u32 *val);
- int pci_write_config_byte(struct pci_dev *dev, int where, u8 val);
- int pci_write_config_word(struct pci_dev *dev, int where, u16 val);
- int pci_write_config_dword(struct pci_dev *dev, int where, u32 val);
- int pci_enable_device(struct pci_dev *dev);
- void pci_disable_device(struct pci_dev *dev);
- void pci_set_master(struct pci_dev *dev);
- int pci_set_dma_mask(struct pci_dev *dev, u64 mask);
- int pci_dac_set_dma_mask(struct pci_dev *dev, u64 mask);
- int pci_assign_resource(struct pci_dev *dev, int i);
- /* Power management related routines */
- int pci_save_state(struct pci_dev *dev, u32 *buffer);
- int pci_restore_state(struct pci_dev *dev, u32 *buffer);
- int pci_set_power_state(struct pci_dev *dev, int state);
- int pci_enable_wake(struct pci_dev *dev, u32 state, int enable);
- int pci_generic_suspend_save(struct pci_dev *pdev, u32 state);
- int pci_generic_resume_restore(struct pci_dev *pdev);
- /* Helper functions for low-level code (drivers/pci/setup-[bus,res].c) */
- int pci_claim_resource(struct pci_dev *, int);
- void pci_assign_unassigned_resources(void);
- void pdev_enable_device(struct pci_dev *);
- void pdev_sort_resources(struct pci_dev *, struct resource_list *, u32);
- unsigned long pci_bridge_check_io(struct pci_dev *);
- void pci_fixup_irqs(u8 (*)(struct pci_dev *, u8 *),
- int (*)(struct pci_dev *, u8, u8));
- #define HAVE_PCI_REQ_REGIONS
- int pci_request_regions(struct pci_dev *, char *);
- void pci_release_regions(struct pci_dev *);
- /* New-style probing supporting hot-pluggable devices */
- int pci_register_driver(struct pci_driver *);
- void pci_unregister_driver(struct pci_driver *);
- void pci_insert_device(struct pci_dev *, struct pci_bus *);
- void pci_remove_device(struct pci_dev *);
- struct pci_driver *pci_dev_driver(const struct pci_dev *);
- const struct pci_device_id *pci_match_device(const struct pci_device_id *ids, const struct pci_dev *dev);
- void pci_announce_device_to_drivers(struct pci_dev *);
- unsigned int pci_do_scan_bus(struct pci_bus *bus);
- struct pci_bus * pci_add_new_bus(struct pci_bus *parent, struct pci_dev *dev, int busnr);
- #endif /* CONFIG_PCI */
- /* kmem_cache style wrapper around pci_alloc_consistent() */
- struct pci_pool *pci_pool_create (const char *name, struct pci_dev *dev,
- size_t size, size_t align, size_t allocation, int flags);
- void pci_pool_destroy (struct pci_pool *pool);
- void *pci_pool_alloc (struct pci_pool *pool, int flags, dma_addr_t *handle);
- void pci_pool_free (struct pci_pool *pool, void *vaddr, dma_addr_t addr);
- /* Include architecture-dependent settings and functions */
- #include <asm/pci.h>
- /*
- * If the system does not have PCI, clearly these return errors. Define
- * these as simple inline functions to avoid hair in drivers.
- */
- #ifndef CONFIG_PCI
- static inline int pcibios_present(void) { return 0; }
- static inline int pcibios_find_class (unsigned int class_code, unsigned short index, unsigned char *bus, unsigned char *dev_fn)
- { return PCIBIOS_DEVICE_NOT_FOUND; }
- #define _PCI_NOP(o,s,t)
- static inline int pcibios_##o##_config_##s (u8 bus, u8 dfn, u8 where, t val)
- { return PCIBIOS_FUNC_NOT_SUPPORTED; }
- static inline int pci_##o##_config_##s (struct pci_dev *dev, int where, t val)
- { return PCIBIOS_FUNC_NOT_SUPPORTED; }
- #define _PCI_NOP_ALL(o,x) _PCI_NOP(o,byte,u8 x)
- _PCI_NOP(o,word,u16 x)
- _PCI_NOP(o,dword,u32 x)
- _PCI_NOP_ALL(read, *)
- _PCI_NOP_ALL(write,)
- static inline struct pci_dev *pci_find_device(unsigned int vendor, unsigned int device, const struct pci_dev *from)
- { return NULL; }
- static inline struct pci_dev *pci_find_class(unsigned int class, const struct pci_dev *from)
- { return NULL; }
- static inline struct pci_dev *pci_find_slot(unsigned int bus, unsigned int devfn)
- { return NULL; }
- static inline struct pci_dev *pci_find_subsys(unsigned int vendor, unsigned int device,
- unsigned int ss_vendor, unsigned int ss_device, const struct pci_dev *from)
- { return NULL; }
- static inline void pci_set_master(struct pci_dev *dev) { }
- static inline int pci_enable_device(struct pci_dev *dev) { return -EIO; }
- static inline void pci_disable_device(struct pci_dev *dev) { }
- static inline int pci_module_init(struct pci_driver *drv) { return -ENODEV; }
- static inline int pci_set_dma_mask(struct pci_dev *dev, u64 mask) { return -EIO; }
- static inline int pci_dac_set_dma_mask(struct pci_dev *dev, u64 mask) { return -EIO; }
- static inline int pci_assign_resource(struct pci_dev *dev, int i) { return -EBUSY;}
- static inline int pci_register_driver(struct pci_driver *drv) { return 0;}
- static inline void pci_unregister_driver(struct pci_driver *drv) { }
- static inline int scsi_to_pci_dma_dir(unsigned char scsi_dir) { return scsi_dir; }
- static inline int pci_find_capability (struct pci_dev *dev, int cap) {return 0; }
- static inline const struct pci_device_id *pci_match_device(const struct pci_device_id *ids, const struct pci_dev *dev) { return NULL; }
- /* Power management related routines */
- static inline int pci_save_state(struct pci_dev *dev, u32 *buffer) { return 0; }
- static inline int pci_restore_state(struct pci_dev *dev, u32 *buffer) { return 0; }
- static inline int pci_set_power_state(struct pci_dev *dev, int state) { return 0; }
- static inline int pci_enable_wake(struct pci_dev *dev, u32 state, int enable) { return 0; }
- #define pci_for_each_dev(dev)
- for(dev = NULL; 0; )
- #else
- /*
- * a helper function which helps ensure correct pci_driver
- * setup and cleanup for commonly-encountered hotplug/modular cases
- *
- * This MUST stay in a header, as it checks for -DMODULE
- */
- static inline int pci_module_init(struct pci_driver *drv)
- {
- int rc = pci_register_driver (drv);
- if (rc > 0)
- return 0;
- /* iff CONFIG_HOTPLUG and built into kernel, we should
- * leave the driver around for future hotplug events.
- * For the module case, a hotplug daemon of some sort
- * should load a module in response to an insert event. */
- #if defined(CONFIG_HOTPLUG) && !defined(MODULE)
- if (rc == 0)
- return 0;
- #else
- if (rc == 0)
- rc = -ENODEV;
- #endif
- /* if we get here, we need to clean up pci driver instance
- * and return some sort of error */
- pci_unregister_driver (drv);
-
- return rc;
- }
- #endif /* !CONFIG_PCI */
- /* these helpers provide future and backwards compatibility
- * for accessing popular PCI BAR info */
- #define pci_resource_start(dev,bar) ((dev)->resource[(bar)].start)
- #define pci_resource_end(dev,bar) ((dev)->resource[(bar)].end)
- #define pci_resource_flags(dev,bar) ((dev)->resource[(bar)].flags)
- #define pci_resource_len(dev,bar)
- ((pci_resource_start((dev),(bar)) == 0 &&
- pci_resource_end((dev),(bar)) ==
- pci_resource_start((dev),(bar))) ? 0 :
-
- (pci_resource_end((dev),(bar)) -
- pci_resource_start((dev),(bar)) + 1))
- /* Similar to the helpers above, these manipulate per-pci_dev
- * driver-specific data. Currently stored as pci_dev::driver_data,
- * a void pointer, but it is not present on older kernels.
- */
- static inline void *pci_get_drvdata (struct pci_dev *pdev)
- {
- return pdev->driver_data;
- }
- static inline void pci_set_drvdata (struct pci_dev *pdev, void *data)
- {
- pdev->driver_data = data;
- }
- /*
- * The world is not perfect and supplies us with broken PCI devices.
- * For at least a part of these bugs we need a work-around, so both
- * generic (drivers/pci/quirks.c) and per-architecture code can define
- * fixup hooks to be called for particular buggy devices.
- */
- struct pci_fixup {
- int pass;
- u16 vendor, device; /* You can use PCI_ANY_ID here of course */
- void (*hook)(struct pci_dev *dev);
- };
- extern struct pci_fixup pcibios_fixups[];
- #define PCI_FIXUP_HEADER 1 /* Called immediately after reading configuration header */
- #define PCI_FIXUP_FINAL 2 /* Final phase of device fixups */
- void pci_fixup_device(int pass, struct pci_dev *dev);
- extern int pci_pci_problems;
- #define PCIPCI_FAIL 1
- #define PCIPCI_TRITON 2
- #define PCIPCI_NATOMA 4
- #define PCIPCI_VIAETBF 8
- #define PCIPCI_VSFX 16
- #endif /* __KERNEL__ */
- #endif /* LINUX_PCI_H */