English
- mainmenu_option next_comment
- comment 'Drivers for ETRAX 100LX built-in interfaces'
- bool 'Ethernet support' CONFIG_ETRAX_ETHERNET
- if [ "$CONFIG_ETRAX_ETHERNET" = "y" ]; then
- # this is just so that the user does not have to go into the
- # normal ethernet driver section just to enable ethernetworking
- define_bool CONFIG_NET_ETHERNET y
- choice 'Network LED behavior'
- "LED_on_when_link CONFIG_ETRAX_NETWORK_LED_ON_WHEN_LINK
- LED_on_when_activity CONFIG_ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY"
- LED_on_when_activity
- else
- define_bool CONFIG_NET_ETHERNET n
- fi
- bool 'Etrax Ethernet slave support (over lp0/1)' CONFIG_ETRAX_ETHERNET_LPSLAVE
- if [ "$CONFIG_ETRAX_ETHERNET_LPSLAVE" = "y" ]; then
- bool ' Slave has its own LEDs' CONFIG_ETRAX_ETHERNET_LPSLAVE_HAS_LEDS
- fi
- bool 'Serial-port support' CONFIG_ETRAX_SERIAL
- if [ "$CONFIG_ETRAX_SERIAL" = "y" ]; then
- # bool ' Use fast timers for DMA flush and RS-485 timing' CONFIG_ETRAX_SERIAL_FAST_TIMER n
- define_bool CONFIG_ETRAX_SERIAL_FAST_TIMER n
- if [ "$CONFIG_ETRAX_SERIAL_FAST_TIMER" = "n" ]; then
- bool ' Fast serial port DMA flush' CONFIG_ETRAX_SERIAL_FLUSH_DMA_FAST
- if [ "$CONFIG_ETRAX100_SERIAL_FLUSH_DMA_FAST" = "n" ]; then
- int ' Receive flush timeout (ticks) ' CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS 5
- fi
- fi
- bool ' Serial port 0 enabled' CONFIG_ETRAX_SERIAL_PORT0
- if [ "$CONFIG_ETRAX_SERIAL_PORT0" = "y" ]; then
- bool ' Ser0 DTR, RI, DSR, CD on PB' CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_ON_PB
- if [ "$CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_ON_PB" = "y" ]; then
- int ' Ser0 DTR on PB bit' CONFIG_ETRAX_SER0_DTR_ON_PB_BIT 4
- int ' Ser0 RI on PB bit' CONFIG_ETRAX_SER0_RI_ON_PB_BIT 5
- int ' Ser0 DSR on PB bit' CONFIG_ETRAX_SER0_DSR_ON_PB_BIT 6
- int ' Ser0 CD on PB bit' CONFIG_ETRAX_SER0_CD_ON_PB_BIT 7
- fi
- fi
- bool ' Serial port 1 enabled' CONFIG_ETRAX_SERIAL_PORT1
- if [ "$CONFIG_ETRAX_SERIAL_PORT1" = "y" ]; then
- bool ' Ser1 DTR, RI, DSR, CD on PB' CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_ON_PB
- if [ "$CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_ON_PB" = "y" ]; then
- int ' Ser1 DTR on PB bit' CONFIG_ETRAX_SER1_DTR_ON_PB_BIT 4
- int ' Ser1 RI on PB bit' CONFIG_ETRAX_SER1_RI_ON_PB_BIT 5
- int ' Ser1 DSR on PB bit' CONFIG_ETRAX_SER1_DSR_ON_PB_BIT 6
- int ' Ser1 CD on PB bit' CONFIG_ETRAX_SER1_CD_ON_PB_BIT 7
- fi
- fi
- if [ "$CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_ON_PB" = "y" -a
- "$CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_ON_PB" = "y" ]; then
- comment 'Make sure you dont have the same PB bits more than once!'
- fi
- bool ' Serial port 2 enabled' CONFIG_ETRAX_SERIAL_PORT2
- if [ "$CONFIG_ETRAX_SERIAL_PORT2" = "y" ]; then
- bool ' Ser2 DTR, RI, DSR, CD on PA' CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_ON_PA
- if [ "$CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_ON_PA" = "y" ]; then
- int ' Ser2 DTR on PA bit' CONFIG_ETRAX_SER2_DTR_ON_PA_BIT 4
- int ' Ser2 RI on PA bit' CONFIG_ETRAX_SER2_RI_ON_PA_BIT 5
- int ' Ser2 DSR on PA bit' CONFIG_ETRAX_SER2_DSR_ON_PA_BIT 6
- int ' Ser2 CD on PA bit' CONFIG_ETRAX_SER2_CD_ON_PA_BIT 7
- fi
- fi
- bool ' Serial port 3 enabled' CONFIG_ETRAX_SERIAL_PORT3
- bool ' RS-485 support' CONFIG_ETRAX_RS485
- if [ "$CONFIG_ETRAX_RS485" = "y" ]; then
- bool ' RS-485 mode on PA' CONFIG_ETRAX_RS485_ON_PA
- if [ "$CONFIG_ETRAX_RS485_ON_PA" = "y" ]; then
- int ' RS-485 mode on PA bit' CONFIG_ETRAX_RS485_ON_PA_BIT 3
- fi
- bool ' Disable serial receiver' CONFIG_ETRAX_RS485_DISABLE_RECEIVER
- fi
- fi
- bool 'Synchronous serial port support' CONFIG_ETRAX_SYNCHRONOUS_SERIAL
- if [ "$CONFIG_ETRAX_SYNCHRONOUS_SERIAL" = "y" ]; then
- bool ' Synchronous serial port 0 enabled' CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT0
- if [ "$CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT0" = "y" ]; then
- bool ' Synchronous serial port 0 uses DMA' CONFIG_ETRAX_SYNCHRONOUS_SERIAL0_DMA
- fi
- bool ' Synchronous serial port 1 enabled' CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT1
- if [ "$CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT1" = "y" ]; then
- bool ' Synchronous serial port 1 uses DMA' CONFIG_ETRAX_SYNCHRONOUS_SERIAL1_DMA
- fi
- fi
- bool 'Parallel port support' CONFIG_ETRAX_PARPORT
- if [ "$CONFIG_ETRAX_PARPORT" = "y" ]; then
- bool ' Parallel port 0 enabled' CONFIG_ETRAX_PARALLEL_PORT0
- bool ' Parallel port 1 enabled' CONFIG_ETRAX_PARALLEL_PORT1
- # here we define the CONFIG_'s necessary to enable parallel port support
- define_tristate CONFIG_PARPORT y
- define_bool CONFIG_PARPORT_1284 y
- define_tristate CONFIG_PRINTER y
- else
- define_tristate CONFIG_PARPORT n
- define_bool CONFIG_PARPORT_1284 n
- define_tristate CONFIG_PRINTER n
- fi
- bool 'ATA/IDE support' CONFIG_ETRAX_IDE
- if [ "$CONFIG_ETRAX_IDE" = "y" ]; then
- # here we should add the CONFIG_'s necessary to enable the basic
- # general ide drivers so the common case does not need to go
- # into that config submenu. enable disk and CD support. others
- # need to go fiddle in the submenu..
- define_bool CONFIG_IDE y
- define_bool CONFIG_BLK_DEV_IDE y
- define_bool CONFIG_BLK_DEV_IDEDISK y
- define_bool CONFIG_BLK_DEV_IDECD y
- define_bool CONFIG_BLK_DEV_IDEDMA y
- define_bool CONFIG_DMA_NONPCI y
- int 'Delay for drives to regain consciousness' CONFIG_ETRAX_IDE_DELAY 15
- choice 'IDE reset pin'
- "Port_PB_Bit_7 CONFIG_ETRAX_IDE_PB7_RESET
- Port_G_Bit_27 CONFIG_ETRAX_IDE_G27_RESET
- Port_CSE1_Bit_16 CONFIG_ETRAX_IDE_CSE1_16_RESET
- Port_CSP0_Bit_08 CONFIG_ETRAX_IDE_CSP0_8_RESET" Port_PB_Bit_7
- else
- define_bool CONFIG_IDE n
- fi
- bool 'Axis flash-map support' CONFIG_ETRAX_AXISFLASHMAP
- if [ "$CONFIG_ETRAX_AXISFLASHMAP" = "y" ]; then
- int ' Byte-offset of partition table sector' CONFIG_ETRAX_PTABLE_SECTOR 65536
- # here we define the CONFIG_'s necessary to enable MTD support
- # for the flash
- define_bool CONFIG_MTD y
- define_bool CONFIG_MTD_CFI y
- define_bool CONFIG_MTD_CFI_INTELEXT n
- define_bool CONFIG_MTD_CFI_AMDSTD y
- define_bool CONFIG_MTD_AMDSTD y
- define_bool CONFIG_MTD_CHAR y
- define_bool CONFIG_MTD_BLOCK y
- define_bool CONFIG_MTD_PARTITIONS y
- fi
- bool 'I2C support' CONFIG_ETRAX_I2C
- if [ "$CONFIG_ETRAX_I2C" = "y" ]; then
- # this is true for most products since PB-I2C seems to be somewhat
- # flawed..
- bool 'I2C uses PB not PB-I2C' CONFIG_ETRAX_I2C_USES_PB_NOT_PB_I2C
- fi
- bool 'I2C EEPROM (non-volatile RAM) support' CONFIG_ETRAX_I2C_EEPROM
- if [ "$CONFIG_ETRAX_I2C_EEPROM" = "y" ]; then
- choice ' EEPROM size'
- "Probed CONFIG_ETRAX_I2C_EEPROM_PROBE
- 2kB CONFIG_ETRAX_I2C_EEPROM_2KB
- 8kB CONFIG_ETRAX_I2C_EEPROM_8KB
- 16kB CONFIG_ETRAX_I2C_EEPROM_16KB" Probed
- fi
- bool 'GPIO support' CONFIG_ETRAX_GPIO
- if [ "$CONFIG_ETRAX_GPIO" = "y" ]; then
- hex ' PA-buttons bitmask' CONFIG_ETRAX_PA_BUTTON_BITMASK 02
- hex ' PA user changeable dir mask' CONFIG_ETRAX_PA_CHANGEABLE_DIR 00
- hex ' PA user changeable bits mask' CONFIG_ETRAX_PA_CHANGEABLE_BITS FF
- hex ' PB user changeable dir mask' CONFIG_ETRAX_PB_CHANGEABLE_DIR 00
- hex ' PB user changeable bits mask' CONFIG_ETRAX_PB_CHANGEABLE_BITS FF
- fi
- bool 'ARTPEC-1 support' CONFIG_JULIETTE
- if [ "$CONFIG_JULIETTE" = "y" ]; then
- source arch/cris/drivers/juliette/Config.in
- fi
- bool 'USB host' CONFIG_ETRAX_USB_HOST
- if [ "$CONFIG_ETRAX_USB_HOST" = "y" ]; then
- define_bool CONFIG_USB y
- bool ' USB port 1 enabled' CONFIG_ETRAX_USB_HOST_PORT1
- bool ' USB port 2 enabled' CONFIG_ETRAX_USB_HOST_PORT2
- else
- define_bool CONFIG_USB n
- fi
- bool 'DS1302 Real Time Clock support' CONFIG_ETRAX_DS1302
- if [ "$CONFIG_ETRAX_DS1302" = "y" ]; then
- bool ' DS1302 RST on Generic Port' CONFIG_ETRAX_DS1302_RST_ON_GENERIC_PORT
- int ' DS1302 RST bit number' CONFIG_ETRAX_DS1302_RSTBIT 2
- int ' DS1302 SCL bit number' CONFIG_ETRAX_DS1302_SCLBIT 1
- int ' DS1302 SDA bit number' CONFIG_ETRAX_DS1302_SDABIT 0
- fi
- endmenu
