3DVisualizer
文件大小: unknow
源码售价: 5 个金币 积分规则     积分充值
资源说明:Vrui-based 3DVisualizer by Oliver Kreylos
========================================================================
README for 3D Visualizer version 1.7
Copyright (c) 2005-2009 Oliver Kreylos
========================================================================

Overview
========

3D Visualizer is a highly interactive application for visualization and
analysis of 3D multivariate gridded data, such as produced by finite
element method (FEM) simulations, confocal microscopy, serial
sectioning, computerized axial tomography (CAT) scans, or magnetic
resonance imaging (MRI) scans. 3D Visualizer is based on the Vrui
software development toolkit (see
http://idav.ucdavis.edu/~okreylos/ResDev/Vrui), and runs in a variety of
environments ranging from laptop or desktop computers over semi-
immersive environments such as Geowalls to fully immersive virtual
reality environments such as CAVEs. More information about 3D Visualizer
can be found at http://www.keckcaves.org.

3D Visualizer's development was supported by the University of
California, Davis, by the UC Davis W.M. Keck Center for Active
Visualization in the Earth Sciences (KeckCAVES,
http://www.keckcaves.org), and the W.M Keck Foundation.

Requirements
============

3D Visualizer requires Vrui version 1.0 build 063 or newer.
To read images in PNG format, libpng has to be installed, and Vrui has
to be configured with support for PNG images (see Vrui README file).

Installation Guide
==================

It is recommended to download or move the source packages for Vrui and
3D Visualizer into a src directory underneath the user's home
directory. Otherwise, references to ~/src in the following instructions
need to be changed.

It is also recommended to skip optional steps 4 and 6 in the following
instructions. 3D Visualizer does not need to be installed in order to
be used; installation (to a system directory such as /usr/local) is
only recommended if 3D Visualizer will be used from multiple user
accounts.

0. Install Vrui from ~/src/Vrui-1.0 (see Vrui README file).

1. Change into ~/src directory and unpack the 3D Visualizer tarball:
   > cd ~/src
   > tar xfz /3DVisualizer-.tar.gz
   - or -
   > tar xf /3DVisualizer-.tar

2. Change into 3D Visualizer base directory:
   > cd 3DVisualizer-

3. Adapt makefile if Vrui installation path is *not* ~/Vrui-1.0 by
   setting the VRUIDIR variable to the correct location. VRUIDIR is
   *not* the directory containing Vrui's sources (and the Vrui README
   file), but the directory specified via the INSTALLDIR variable in
   Vrui's makefile.

4. Optional: Adapt makefile if 3D Visualizer is to be installed in a
   different location, for example /usr/local. Set INSTALLDIR to the
   desired target location. 3D Visualizer will be then be installed in
   $(INSTALLDIR)/bin, $(INSTALLDIR)/lib (or $(INSTALLDIR)/lib64 on
   64-bit Linux systems), and $(INSTALLDIR)/share.
   Important note: Do not use ~ as a shortcut for the user's home
   directory here; use $(HOME) instead. For example, write
   INSTALLDIR = $(HOME)/apps
   instead of
   INSTALLDIR = ~/apps

5. Build 3D Visualizer:
   > make

6. Optional: Install 3D Visualizer in the selected target location.
   This is only necessary if the INSTALLDIR variable in the makefile
   was changed. By default, 3D Visualizer can be run from its base
   directory. To install:
   > make install
   - or, if the target location is a system directory -
   > sudo make install

7. Optional: Add directory containing the 3D Visualizer executable
   (~/src/3DVisualizer-/bin in the default installation,
   $(INSTALLDIR)/bin otherwise) to the user's search path. This allows
   running 3D Visualizer from any directory. Using csh or tcsh:
   > setenv PATH ${PATH}:~/src/3DVisualizer-/bin
   - or -
   > setenv PATH ${PATH}:/bin
   where  is the target location set in the makefile.
   Using bash:
   > export PATH=${PATH}:~/src/3DVisualizer-/bin
   - or -
   > export PATH=${PATH}:/bin
   These lines can also be added to the user's .cshrc or .bashrc files
   to make the additions persist between logins.

Running 3D Visualizer on Alaska Example Data
============================================

These instructions assume that 3D Visualizer was installed in its base
directory, (see steps 4 and 6 above).

1. Change into 3D Visualizer base directory:
   > cd ~/src/3DVisualizer-

2. Download example data tarball AlaskaData.tar.gz.

3. Unpack example data tarball in 3D Visualizer directory:
   > tar xfz /AlaskaData.tar.gz
   - or -
   > tar xf /AlaskaData.tar

4. On MacOS X: Start X11. 3D Visualizer requires a running X server,
   but, if preferred, it can be started from a MacOS X terminal instead
   of xterm.

5. Run 3D Visualizer on example data:
   > ./bin/3DVisualizer -palette AlaskaData/slab2.pal
     AlaskaData/slab2.in
   - or (full command line) -
   > ./bin/3DVisualizer -palette AlaskaData/slab2.pal
     -class MultiCitcomtFile AlaskaData/slab2.dat Temp "log(Visc)"

6. See Vrui-1.0 documentation or 3D Visualizer's user's guide on Vrui's
   basic user interface and how to use 3D Visualizer.

本源码包内暂不包含可直接显示的源代码文件,请下载源码包。