English
资源说明：Modular APRS Tracker Project for PIC18. Work in progress. See REAME and Issues
PIC18 Based APRS Tracker Project
================================
This is an APRS tracker project targetted at PIC18.
It is initially very incomplete!
The intended use of this was for situations where I am working with both St John and RAYNET as a cycle responder. I hope to be able to use the device with a mic, so I can still talk into the radio rather than having the radio tied up. It would be nice to be able to use the Mic-E status codes and message to indicate
status.
There is a fair amount of other Tracker source out there if you look for this. Much of it is for PIC16. Some of it needs the Hi-Tech C compiler with its optimisations.
As well as being interesting for me, I intend this system to be modular so
esaier to maintain and work on. Someone building this project should be able
to do it using freely available tools - currently possible as long as Microchip
continue to provide a free "Lite" version of their C18 compiler.
The PIC18
---------
The PIC18 is only slightly more expensive than the PIC16 series commonly
used for trackers. It has the following advantages:
* Built in clock that can run up to 32MHz. I had been running at 16MHz.
Microchip claim 2% accuracy within reasonable operating conditions.
Unfortunatly this has not been accurate enough to use with the AGWTracker
receiving the signals. If I can use the internal oscillator, perhaps using
a training technique to adjust it, then I'd cut down on external part
count and cost.
* The VCref voltage reference output makes quite a good digital to
analogue converter, enabling me to output the signal without the
external resistor network. It does need a buffer of some kind to drive
a radio.
* There is good support for C. Even at assembler level there are some nicer op-codes.
The Hardware
------------
I'm developing using a PIC 18F14K50.
My GPS module is the DS-622R (http://www.rfsolutions.co.uk/acatalog/Board_Level_GPS_Receiver_Module.html) from RF Solutions.
This is still reasonably cheap and works amazingly well, even finding a lock (eventually) indoors. It doesn't seem to like saving configuration changes to its
flash RAM, so is stuck at 9600 baud. Not a problem here. Output is LVTTL.
I have an old LCD display hanging around. I'm rapidly running out of pins to drive it.
The radio is a Yaesu VX-7R. That should not matter.
Both PIC and GPS can run low voltage, which offers interesting options for low power. The LCD looks very power hungry.
Pin assignment so far: (Items in brackets can be worked around or changed)
* RA4 AN3 Audio in from radio. Central bias. To detect Busy, and one day to decode?
* RB5 RX GPS module, or computer for programming
* RB7 TX Computer for programming. Could use as something else when not talking to computer?
Assumes I can get away without having to send commands to the GPS.
* RC2 Cvref Audio out to radio.
I will need to assign PTT IN, PTT OUT and whatever controls I may use. Maybe the two PTTs could be combined,
though that could increase external circuitry.
The State of Play
-----------------
* I now have AX25 wave generation complete.
See http://www.flickr.com/photos/m0rjc/6041105197/in/photostream/lightbox/
A possible improvement would be to time the bit transitions more accurately,
either using a second timer or counting ticks in RAM.
* I have Generated and "transmited" a hard coded test message. I could receive it using APRS software with the output from the PIC connected to the PC's mic input.
The Plan
--------
* Receive information from the GPS module in interrupts using a state machine.
I am working on a state engine generator to make this easier to create and maintain.
This has now been forked into its own repository (m0rjc/PICStateMachineGenerator).
The same generator can then be used for command interface, or maybe decoding?
* Provide a means to detect "Radio Busy".
- By detecting audio from the radio.
- Research how I can detect PTT on a connected microphone.
- If possible use the same pin to detect "Busy" on the data port of a radio like the Yaesu 8900.
* Complete the basic Tracker functions to create a first functioning prototype. Use the simplest encoding possible.
Call this Milestone 1
* I've had to use a crystal to give the stability. It would be interesting to use the internal clock and tune it using the 1 pulse per second output from the GPS module.
* Either complete the Mic-E encoder in assembly, or start again in C. I have now removed the part written code, and having blatted the repository I'd have to go to my own backups to restore it if I want to return to it. I'm not sure how useful compression is for a device like this - apart from perhaps reducing the amount of time during the transmission for clock skew to set in.
* I've had an LCD display in my bits box for ages, so this is becoming more singing and dancing then maybe it could be. Write code to output information to it, but keep it all modular so someone else could use this code in a much more lightweight way. The way things are going I may have to look at it as an expansion using the I2C bus.
Very Long Term:
---------------
* I plan to use an ADC input to detect incoming signal from the radio.
Find a way of decoding incoming data. A couple of options present themselves:
- The DTMF Decoder algorithms. I've not seen them settle in the past. Maybe I got them wrong.
- Could I make a trellis decoder based on samples? How about sign and sign of rate of change? The latter
is a natural Gray Code, and may not need frequent sampling. I'd need to lock phase
(use a comparater to detect zero crossing perhaps?) and somehow ensure I
know the signal amplitude to work out the trellises. (easy peak detector)
It would take some investigation to see if it's possble given resources.
Theoretically given a sample I should be able to work out where
the next sample will be for either of the two tone frequencies and compare.
* If I can decode then that opens up some interesting possibilities
* Receive messages?
* Digipeat?
* Show other stations on a connected Garmin Etrex? The limit would be time, and the amount of program and data space in the microcontroller.
* Experiment with smart track algorithms. I have some interesting ideas. I don't know how easy they would be.
本源码包内暂不包含可直接显示的源代码文件，请下载源码包。
